| |
|
|
|
|
|
|
| Quikmount
4 - An affordable cold laminator |
.tmp) |
| |
|
|
|
|
|
|
| |
Great for
laminating, mounting prints to boards or applying transfer
tapes |
.tmp) |
|
| |
|
Provides many features found in
more expensive
laminators:
• Heavy
duty motor
• Automatic
take up shaft
• Shaft for
liner paper in front
• Silicone covered
rollers
•
Rugged steel and aluminum
construction |
|
.tmp) | |
| |
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
Quikmount makes laminating easy. Just
follow a few simple steps: |
| |
|
|
|
.tmp) |
| |
|
|
|
|
|
|
1. Insert the hubs into the laminate
core (all laminate rolls
have
3" cores)
|
|
.tmp) |
| |
|
|
|
2. Shafts lift easily out of channels,
so laminate rolls can be
changed
quickly. Collars keep the
rolls
in place on the shaft.
|
|
.tmp) |
| |
|
|
3. Two pulleys (one is hidden
in
the photo) and a belt drive
the take up shaft
|
|
.tmp) |
| |
|
|
4. Two knobs set the height
and
pressure of top roller (it is
easy
to set the pressure
properly)
Accepts boards up to 1"
thick.
|
|
.tmp) |
| |
|
|
5. Thread liner paper (from
front
shaft) between the rollers.
This
will keep the laminate
from
sticking to the rollers while
laminating.
|
|
.tmp) |
| |
|
|
6. Tape release paper (from
back of laminate) to core
on take up shaft.
|
|
.tmp) |
| |
|
|
7. Thread laminate through
rollers.
|
|
.tmp) |
| |
|
|
8. Run your print through
the
rollers.
|
|
.tmp) |
| |
|
| |
| |
|
|
|
|
|
After the print exits out the back, go to the
back of the laminator, cut off the laminate, trim and you have
a perfectly laminated print. You can then simply run through
the next print without going through any more set up since the
laminate and liner paper are already threaded through the
rollers.
|
| |
|
|
|
|
|
|
| |
|
|
|
Options |
|
|
| |
|
|
|
|
|
Stand |
| |
|
|
|
|
|
Rolling stand is made from steel with four
castors. It makes your Quikmount 4 mobile, while saving table
space. Silver entry deck is 37" high when placed on
stand. |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
.tmp)
|
| |
|
|
|
|
|
Footswitch |
| |
|
|
|
|
|
Footswitch provides hands free
control. |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
.tmp)
|
| |
|
|
|
Cold Laminates |
|
|
| |
|
|
|
|
| |
|
|
|
|
|
Daige carries a full line of cold laminates in
three finishes: gloss, luster or matte. Gloss is normally used
when you need to add glossiness to your finished print.
Luster, the most popular finish, is used indoors to eliminate
glare and provides a very natural look. Matte is used when you
want to tone down the finish. Available in 25", 38", 51" and
54" widths. |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
Mounting |
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
Apply mounting adhesive |
| |
|
|
|
|
|
Place a roll of mounting adhesive on the back
shaft (for most adhesives you do not need the take up shaft).
Run your board through to apply adhesive. It comes out with a
release paper covering the adhesive on the board so you can
use it at any time. |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
.tmp)
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
Mount prints to boards |
| |
|
|
|
|
|
Pull back the first two inches of the release
liner covering your board or media to expose the adhesive.
Position your print on the board, then rub down the first two
inches to the exposed adhesive.
Place the board/print
into the Quikmount rollers, drape the print over the top
roller (as shown in photo) and run it through the rollers. You
get a smooth mount every time. |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
.tmp)
|
| |
|
|
|
Specifications |
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
Roller Widths |
|
25", 38", 55" or
65" |
|
Board Thickness |
|
up to 1" thick |
|
Speed |
|
8
seconds per foot
(or 7.5 ft. per
minute) |
|
Electrical |
|
110 volt (U.S.) or
230 volts (for
overseas) |
|
Outside Dimensions |
25" |
17" W x 31" L |
|
38" |
17" W x 44" L |
|
55" |
17" W x 61" L |
|
65" |
17" W x 71" L |
|
|
